/dev/dbgctl
/dev/dbglog

echo r >/dev/dbgctl

Dbg uses the values of several global variables set by the kernel configuration file (see conf(10.6)), all of which default values. The variables and default values are listed below:

int dbgstart = 0;
char	*dbgdata = "#t/eia0";
char	*dbgctl = "#t/eia0ctl";
char	*dbgctlstart = "b19200";
char	*dbgctlstop = "h";
char	*dbgctlflush = "f";

Different values can be set by including similar declarations, with values as desired, in the code section of the configuration file. Dbg uses the values as follows:

dbgstart if non-zero, start the debugger protocol on the configured connection during driver initialisation (system startup); otherwise it must be started explicitly by the r control request (see below)

dbgdata

data file for the debugging connection

dbgctl

control file for the debugging connection

dbgctlstart

control request to initialise link (eg, baud rate)

dbgctlstop

control request to hang up link

dbgctlflush

control request to write to flush input and output on link

Dbg serves two files that control and monitor its operation.

Dbgctl accepts several textual commands; normally only r is needed:

d dbgdata

set the value of dbgdata to the value given as an argument

c dbgctl

i dbgctlstart

h dbgctlstop

f dbgctlflush

set the value of the corresponding control variable to the value of the first argument

r

start running the debugger protocol (not needed if dbgstart was non-zero at boot)

s

stop running the debugger protocol; stop and flush the link

When read, dbgctl yields a single line showing the status of the device (`running' or `stopped') and the current values of the debugger control variables listed above.

Dbglog is a read-only text file containing lines representing debugger events, one per line. It is mainly useful for checking the operation of the device, or debugging new acid(10.1) functions.

Debug protocol

The protocol is subject to change. The host running the debugger and the target to be debugged exchange 10-byte messages containing a one byte message type and 9 bytes of data. Bytes unused by a given type are set to zero. Normally the host sends one of the T-messages below and receives the corresponding R-message, or Rerr. (These are unrelated to the T-messages and R-messages of intro(5).) Exceptionally, the target sends the first message, an Rerr to reset the protocol, and thus the debugger is notified if the target is rebooted during a debugging session and can reset its own state. Values, including addresses, are sometimes represented textually in hexadecimal, but are usually in binary as a single byte, or an array of 4 bytes, high-order byte first (big endian).

The term process here refers exclusively to those created directly or indirectly by kproc(10.2), not to Limbo processes, which are not visible directly through the protocol (although it is possible to write acid(10.1) functions that interact through dbg with the Inferno data structures representing the state of the Dis virtual machine). Many requests read or write the memory or state of the current process set by the Tproc message (see below). Addresses are always 32 bits. An address below the size of Ureg (saved register state) for the target is interpreted as an offset within the saved state for the current process. Otherwise it refers to an address in kernel virtual memory. Currently in native Inferno all processes share the same address space.

The message type names used below are assigned values by declarations in /include/rdbg.h. The following messages are currently implemented:

Terr unused

Rerr reason[9]

The last message failed for the given reason, a text string: reset, the target or debug driver was restarted; count, bad count; unk, unknown command; inval, invalid parameter; pid, no such process; unsup, unsupported action; notstop, action requires process to be stopped first.

Tmget addr[4] n[1]

Request n bytes of memory from addr; n must be no greater than 9

Rmget data[9]

Return data requested by Tmget

Tmput addr[4] n[1] data[4]

Write the first n bytes of data to memory at addr, and flush the data and instruction caches for that region; n must be no greater than 4

Rmput

Reply to a successful Tmput

Tproc pid[4]

Set the current process to the one with integer process ID pid for subsequent requests.

Rproc addr[8]

Addr is the address in hexadecimal text of the Proc structure for process pid in the corresponding Tproc.

Tstatus pid[4]

Request the status of process pid leaving the current process ID unchanged.

Rstatus status[9]

Return the textual status of the process as a text string, currently one of: Dead, Moribund, Ready, Scheding, Running, Queueing, Wakeme, Broken, Stopped, Rendezvous, or if invalid, the state value as a hexadecimal number.

Trnote pid[4]

Retrieve the note (trap status) for the given pid

Rrnote status[9]

Provide the textual trap status for the requested process (currently always returns null status)

Tstop pid[4]

Tell the kernel to stop running process pid in debugging state Stopped when it next appears in the scheduler.

Rstop

Reply to successful Tstop

Tstart

Cancel a previous Tstop; if the process has already stopped, make it ready to run.

Rstart

Reply to successful Tstart

Tcondbreak val[4] op[4]

If op is d, remove and delete the breakpoint with ID val. All other operations help create a conditional breakpoint, providing a possibly empty list of operations representing a conditional expression in Reverse Polish is followed by a breakpoint request, each expression element represented by a single Tcondbreak message. Op is a single character representing an operation, with val (integer, address, process ID) as a parameter. The operator n should appear first; it assigns the breakpoint an ID number val (no greater than 255). Expression primaries are: k val, true if process val is at this breakpoint; b val, true if program counter is val; and p val, val as a 32-bit literal. Expression operators are: unary * (indirect, yielding 32-bit value); & (bit-wise AND); = (values equal); ! (values not equal); a (logical AND); o (logical OR). Although the expression is interpreted following Reverse Polish notation, when transmitted, the b operation is sent last (to mark the end of the sequence and create the breakpoint), but is moved to the start of the expression before evaluation.

Rcondbreak

Reply to successful Tcondbreak.

Tstartstop pid[4]

If the process pid is not stopped, return Rerr notstop. Otherwise, if the process is not stopped at a breakpoint, start it, and wait for it to reach a breakpoint that evaluates `true'

Rstartstop id[1]

Process has stopped at breakpoint with the given id

Twaitstop

Unimplemented. See Tstartstop.

Rwaitstop

Unused.

Tkill pid[4] note[5]

Kill process pid with the given textual note. Unimplemented.

Rkill

Reply to successful Tkill. Unused.